
次の流行りはこれかぁ、、。
— Atsushi Hara【原 篤志】@Hara Racing (@Atsushi_Hara1) May 28, 2026
どんどんヘンテコになっていくなぁ、、😔#これでいいのかツーリングカーボディー pic.twitter.com/ZaBCkDLbz0
真横から見るとさらに、、、#これでいいのかツーリングカーボディー pic.twitter.com/Rw4vVJZYPl
— Atsushi Hara【原 篤志】@Hara Racing (@Atsushi_Hara1) May 29, 2026
ラジコンをとっても上手に走らせれられる方の原さん*1が、新作のツーリングカーのボディーについて苦言を呈していたので、私も書いてみます。
これをツーリングカーというのは無理がある
ツーリングカーのボディのルールは下記の通りです。
5.4 BODIES 1/10th ISTC, SPECIFICATIONS:
5.4.1 For the purpose of the IFMAR World Championships, only scale representations of full size FIA Class Two Touring Cars in International Touring Car Series’ (e.g. ITC, BTCC, NATC, Japan Touring Cars, etc.) but restricted to (4) four door bodies will be approved. Bodies must be reproduced with all features in proper proportion to each other. Lines indicating the shut-lines on the full-size car for bonnet (hood), boot (trunk) all doors and windows are to be moulded in to the body shell. Particular attention must be paid to realistic scale proportions. A lower trim line must be moulded into the body shell.
5.4.2 Only body shells which are fully complying with rule 5.4.4 and registered either by IFMAR or one of the blocs may be used. Body shell manufacturers may register with IFMAR at any time, but not less than four months prior to that years' IFMAR World Championship to be eligible for that event. IFMAR approvals are valid for 5 years.
5.4.3 One (1) sample of a body shell, eventually together with photographs of the full-size car (showing at least three (3) views: front, side and rear) on which the body shell is inspired, must be submitted to the IFMAR Electric Section Chairman together with an approval fee of $US200 to be settled at submission. Approval is for 5 years.
5.4.4 All submitted body shells must comply with the “global body specifications” (GBS)
5.4.5 Bodies shall be neatly finished. Details of all front and rear lights and windows must be translucent. Air intakes, front grills, cooling grills and eventual drivers must be clearly contrasted from the surrounding paintwork.
5.4.6 Only One (1) single level rear wing may be used with the body shell.
(出典:ELECTRIC TRACK RACING AND TECHNICAL RULES 1/12th , 1/10th ISTC, FWD & E F1 VERSION /: SEPTEMBER 2024)
初めて原文を読んだんですが、FIAのクラス2準拠って前提が一応あったんですね。
今生き残っているのはBTCCぐらいですが、要はああいうお買い物車ベースの車両をモデルにしたボディである必要性があるわけです。
www.youtube.com
現状は望ましいとはいえない
現行の競技用のツーリングカーのボディはルール5.4.1から著しく逸脱しているように思えます。5.4.4の規定は満たしているのかもしれませんが、とてもFIAのクラス2準拠の車には見えません。FIAのクラス2は大元を辿ればグループAに準拠した車であり、連続した12ヶ月間に月間2500〜5000台を生産するような大衆車、つまり日常の足の車として使えそうな見た目を保持していることは大事なのではないでしょうか?
朝起きて子供達と東京の姉を乗せ、子供達を保育園にあずけて、東京の姉をメンクリに捨てて預けて、その間にジャスコで1日分の買い物をして、メンクリから仕方なく東京の姉を回収して、子供達を保育園に迎えに行き、家に帰る。そう言った何気ない主婦の日常の延長上にありそうなボディをもうちょっと作って欲しいんやでーと運転がヤバい方の原さんも言っているような気がします。知らんけど。
この辺りがギリ保ててるのがFF
FFのハッチバックボディはギリギリFIAのクラス2味がまだある気がしています。
あんまりこっちは過激化しないことを祈っています。
*1:いうまでもなく2000年のISTCと2008年の1:8 IC Off Roadのチャンピオンである